Tom Arlow, owner of Arlow Plumbing & HeatingPressure low? Easy fix.
Help guide

How to top up your heating pressure

Boiler pressure dropped below 1 bar? Here’s how to top it up safely in a few minutes, with a short video from our team.

  • 750+ five-star reviews
  • Gas Safe registered
  • OFTEC registered
  • Gas & oil boilers
Watch the video

See how it’s done

A quick video from the Arlow team showing how to top up the pressure on a typical combi boiler.

Low boiler pressure

Topping up your pressure, step by step

Pressure can drop over time, after bleeding radiators or because of a small leak. When it falls below 1 bar, most boilers stop and show a fault.

Step by step

Aim for 1 to 1.5 bar on the gauge when the heating is off and the system is cold. Check your user guide for your boiler’s exact range.

  1. Turn the boiler off and let the system cool down.
  2. Put an old towel under the boiler to catch any drips.
  3. Find the filling loop or filling key underneath the boiler. Only touch controls you can clearly identify.
  4. Open the valve slowly and watch the pressure gauge. If there are two valves, you may need to open both.
  5. Close the valves fully as soon as the gauge reads between 1 and 1.5 bar.
  6. Turn the boiler back on, and press reset if it’s still showing a fault.

When to call us instead

Topping up once or twice a year is normal. Stop and get in touch if:

  • You’re topping up every month or more often
  • The pressure drops quickly straight after topping up
  • The pressure keeps rising after you’ve closed the valves
  • You can see water leaking from the boiler, pipes or radiators
  • You can’t find or identify the filling controls

Never take the front cover off your boiler. Anything inside it is a job for a Gas Safe engineer.

Good to know

Why boiler pressure drops

Common causes

A small drop now and then is normal. The most common reasons are:

  • Bleeding radiators, which lets a little water out along with the air
  • A small leak on a radiator valve, pipe joint or the boiler itself
  • A worn pressure relief valve letting water out through the pipe outside
  • An expansion vessel that needs re-charging

If the pressure keeps dropping, it’s usually one of the last three, and that’s a job for us.

What the gauge should read

Most boilers should sit between 1 and 1.5 bar when the heating is off and the system is cold. It will rise a little when the heating is on.

  • Below 1 bar: top it up using the steps above
  • 1 to 1.5 bar when cold: just right
  • Around 2.5 bar or more when hot: get in touch, as the system may need checking

Check your boiler’s user guide for its exact range, as it can vary between models.

FAQ

Heating pressure questions answered

What pressure should my boiler be at?
Most boilers should sit between 1 and 1.5 bar when the heating is off and the system is cold. Check your user guide for your boiler’s exact range.
How often should I need to top up?
Once or twice a year is normal. If you’re topping up every month or more often, there’s probably a leak or a fault, so get in touch.
Can I top up with the heating on?
It’s best to top up when the heating is off and the system is cold, so you get an accurate reading on the gauge.
What if I put too much water in?
Bleed a radiator to let a little water out, then check the gauge again. If it stays too high, get in touch.

Still stuck? Send us a photo

WhatsApp a photo of the boiler display, any fault code and the pressure gauge, plus the make and model, to 07761 510503. Or chat with Rosie, our digital assistant, in the chat box at the bottom of the screen.

Plumbing & heating across Somerset

Areas we cover

Based in Bridgwater, our engineers look after homes across Taunton, Burnham-on-Sea and the surrounding towns and villages.

BridgwaterTauntonBurnham-on-SeaHighbridgeNorth PethertonWellingtonCheddarMineheadStreetWeston-super-Mare